Line & Duct Burners
NP-LE AIRFLO®
NP-LE AIRFLO provides direct-fired makeup-air and process heating with lower CO and NO2 than the standard NP family.
NP-LE AIRFLO provides direct-fired makeup-air and process heating with lower CO and NO2 than the standard NP family. The short-flame design supports high heat release per unit length. Low-pressure and corrosion-resistant versions are available, with certification and capacity claims tied to the manufacturer's published direct-air-heating arrangement.
Features & Benefits
- Maximum Upstream Air Temperature
- Downstream: ≤ 1000 deg F (≤ 840 deg F for aluminum bodies)|Upstream:≤ 600 deg F (≤ 450 deg F for aluminum bodies)
- Ignition Transformer Requirement
- ≥ 5000 V/200 VA
- Profile Plate Requirement
- Minimum ~152 mm (6 in) silhouette profile plate surrounding burner leading edge
- Mixing Plate Materials
- Stainless Steel 430 (1.4016)
- Process Air Velocity
- 1700 to 3000 fpm across burner mixing plates
- Maintenance Interval
- Inspect at least annually (more frequently for continuous process duty); do not enlarge ports
- Gas Port Drill Sizes
- #43 typical; #47 at intersections of 12x6 tees and 36 in back‑inlets; NP2‑LE AL uses #47 outside rows/#43 inside
- Burner Section Sizes
- 12 and 36 in back‑inlet sections|12x6 tee|6, 12, 18, 24 in straight|6x6 elbow
- Flame Detection
- Flame rod or UV scanner, depending on end‑plate selection
- Turndown Ratio
- 30:1
- Pilot Capacity
- Nominal 25,000 Btu/h pilot
- Capacity Range
- Max - 1,000,000 Btu/h per lineal foot, Min - 25,000 Btu/h per lineal foot (application‑dependent)
- Pressure Drop
- 0.3 to 1 in wc across burner and profile plate (Process Air)
- Ignition Type
- Raw gas pilot integrated in end plate; direct spark ignition possible per local codes
- Gas Pressure
- Butane - NP1‑LE ≈7.7 mbar (≈3.1 in wc); NP2‑LE ≈3.7 mbar (≈1.5 in wc) for 300 kW/ft|Natural Gas - NP1‑LE ≈31.7 mbar (≈12.7 in wc); NP2‑LE ≈15.2 mbar (≈6.1 in wc) for 300 kW/ft|Propane - NP1‑LE ≈12.8 mbar (≈5.1 in wc); NP2‑LE ≈6.2 mbar (≈2.5 in wc) for 300 kW/ft
- Flame Length
- 150 to 700 mm (6 to 28 in), increasing with heat input and decreasing with higher air velocity
- Burner Type
- In‑duct, direct‑fired line burner for fresh air/process air (raw gas) with profile plate velocity control
- Model Name
- NP1‑LE and NP2‑LE AIRFLO®
- Fuel Type
- Natural Gas, Propane, Butane
- Material
- NP1‑LE: Standard (Cast Iron), AL (Aluminum Body), ALSS (Aluminum Body/Back‑Up Bars, Nickel‑Plated End Plates, Stainless Steel Fasteners)|NP2‑LE: Standard or AL
- A short flame and high output per length support compact installations.
Applications
- Direct-fired makeup-air and process heating
Air/Exhaust/Flue Gas Temperatures
- Maximum Upstream Air Temperature
- Downstream: ≤ 1000 deg F (≤ 840 deg F for aluminum bodies); Upstream:≤ 600 deg F (≤ 450 deg F for aluminum bodies)
Ignition, Flame & Supervision Specifications
- Ignition Transformer Requirement
- ≥ 5000 V/200 VA
- Profile Plate Requirement
- Minimum ~152 mm (6 in) silhouette profile plate surrounding burner leading edge
- Flame Detection
- Flame rod or UV scanner, depending on end‑plate selection
- Ignition Type
- Raw gas pilot integrated in end plate; direct spark ignition possible per local codes
Material Specifications
- Mixing Plate Materials
- Stainless Steel 430 (1.4016)
- Material
- NP1‑LE: Standard (Cast Iron), AL (Aluminum Body), ALSS (Aluminum Body/Back‑Up Bars, Nickel‑Plated End Plates, Stainless Steel Fasteners); NP2‑LE: Standard or AL
Air & Combustion Air Specifications
- Process Air Velocity
- 1700 to 3000 fpm across burner mixing plates
Electrical Specifications
- Maintenance Interval
- Inspect at least annually (more frequently for continuous process duty); do not enlarge ports
Dimensions & Size Specifications
- Gas Port Drill Sizes
- #43 typical; #47 at intersections of 12x6 tees and 36 in back‑inlets; NP2‑LE AL uses #47 outside rows/#43 inside
- Burner Section Sizes
- 12 and 36 in back‑inlet sections; 12x6 tee; 6, 12, 18, 24 in straight; 6x6 elbow
Performance, Flow & Capacity
- Turndown Ratio
- 30:1
Performance Specifications
- Pilot Capacity
- Nominal 25,000 Btu/h pilot
Processing & Performance Metrics
- Capacity Range
- Max - 1,000,000 Btu/h per lineal foot, Min - 25,000 Btu/h per lineal foot (application‑dependent)
Pressure Specifications
- Pressure Drop
- 0.3 to 1 in wc across burner and profile plate (Process Air)
- Gas Pressure
- Butane - NP1‑LE ≈7.7 mbar (≈3.1 in wc); NP2‑LE ≈3.7 mbar (≈1.5 in wc) for 300 kW/ft; Natural Gas - NP1‑LE ≈31.7 mbar (≈12.7 in wc); NP2‑LE ≈15.2 mbar (≈6.1 in wc) for 300 kW/ft; Propane - NP1‑LE ≈12.8 mbar (≈5.1 in wc); NP2‑LE ≈6.2 mbar (≈2.5 in wc) for 300 kW/ft
Burner/Flame‑Related Lengths
- Flame Length
- 150 to 700 mm (6 to 28 in), increasing with heat input and decreasing with higher air velocity
Overview
- Burner Type
- In‑duct, direct‑fired line burner for fresh air/process air (raw gas) with profile plate velocity control
- Model Name
- NP1‑LE and NP2‑LE AIRFLO®
Fuel, Gas & Media Specifications
- Fuel Type
- Natural Gas, Propane, Butane
| Parameter | Published value / configuration |
|---|---|
| Maximum Upstream Air Temperature | Downstream: ≤ 1000 deg F (≤ 840 deg F for aluminum bodies); Upstream:≤ 600 deg F (≤ 450 deg F for aluminum bodies) |
| Ignition Transformer Requirement | ≥ 5000 V/200 VA |
| Profile Plate Requirement | Minimum ~152 mm (6 in) silhouette profile plate surrounding burner leading edge |
| Flame Detection | Flame rod or UV scanner, depending on end‑plate selection |
| Ignition Type | Raw gas pilot integrated in end plate; direct spark ignition possible per local codes |
| Mixing Plate Materials | Stainless Steel 430 (1.4016) |
| Material | NP1‑LE: Standard (Cast Iron), AL (Aluminum Body), ALSS (Aluminum Body/Back‑Up Bars, Nickel‑Plated End Plates, Stainless Steel Fasteners); NP2‑LE: Standard or AL |
| Process Air Velocity | 1700 to 3000 fpm across burner mixing plates |
| Maintenance Interval | Inspect at least annually (more frequently for continuous process duty); do not enlarge ports |
| Gas Port Drill Sizes | #43 typical; #47 at intersections of 12x6 tees and 36 in back‑inlets; NP2‑LE AL uses #47 outside rows/#43 inside |
| Burner Section Sizes | 12 and 36 in back‑inlet sections; 12x6 tee; 6, 12, 18, 24 in straight; 6x6 elbow |
| Turndown Ratio | 30:1 |
| Pilot Capacity | Nominal 25,000 Btu/h pilot |
| Capacity Range | Max - 1,000,000 Btu/h per lineal foot, Min - 25,000 Btu/h per lineal foot (application‑dependent) |
| Pressure Drop | 0.3 to 1 in wc across burner and profile plate (Process Air) |
| Gas Pressure | Butane - NP1‑LE ≈7.7 mbar (≈3.1 in wc); NP2‑LE ≈3.7 mbar (≈1.5 in wc) for 300 kW/ft; Natural Gas - NP1‑LE ≈31.7 mbar (≈12.7 in wc); NP2‑LE ≈15.2 mbar (≈6.1 in wc) for 300 kW/ft; Propane - NP1‑LE ≈12.8 mbar (≈5.1 in wc); NP2‑LE ≈6.2 mbar (≈2.5 in wc) for 300 kW/ft |
| Flame Length | 150 to 700 mm (6 to 28 in), increasing with heat input and decreasing with higher air velocity |
| Burner Type | In‑duct, direct‑fired line burner for fresh air/process air (raw gas) with profile plate velocity control |
| Model Name | NP1‑LE and NP2‑LE AIRFLO® |
| Fuel Type | Natural Gas, Propane, Butane |
Values retain manufacturer model qualifications. Review Honeywell specifications ↗
Part Number
Published part numbers
10 parts
| Part Number | Description | Enquiry |
|---|---|---|
| 1049071 | MTL SHIM GSKT | Request quotation |
| 1049073 | 6" MXG PLT | Request quotation |
| 1049074 | IN CRNR MXG PLT | Request quotation |
| 1049075 | WDG MXG PLT | Request quotation |
| 1049076 | DIV PLT | Request quotation |
| 1050373 | 6" STR CI BDY | Request quotation |
| 1050375 | 6" STR BDY AL | Request quotation |
| 1050376 | 12" STR CI BDY | Request quotation |
| 1050384 | 12" STR BDY AL | Request quotation |
| 1050385 | 12" BACK INLT CI BDY | Request quotation |
Manufacturer sources
Last source check: 2026-11-02
NP-LE Airflo Product Image · Manufacturer ownership retained; republication licence not independently confirmed
ABID Automation LTD maintains this independent product reference. Honeywell owns its product names and trademarks. Current manufacturer documentation governs specification, availability and certification.
Your next project. A clear starting point.
Tell us about your facility and what you need to achieve.
