Direct Fired Furnace Burners
WHG Wall Hugger
WHG uses a wall-following flame to heat through furnace-wall and roof radiation while avoiding direct impingement on the load.
WHG uses a wall-following flame to heat through furnace-wall and roof radiation while avoiding direct impingement on the load. It supports direct-spark or pilot ignition and UV or flame-rod supervision. The source describes stable cold-furnace operation and rapid movement to high fire, with preheated-air capability up to 425°C.
Features & Benefits
- Air Temperature Range
- Preheated air up to 800 deg F (425 deg C)
- Turndown Capability
- Stable operation from low fire to high fire (model‑dependent)
- Primary Function
- Even heat distribution with no flame impingement
- Operation Stability
- Stable in cold furnace at low excess air
- Operating Modes
- On‑ratio firing; operation with excess air
- Maximum Chamber Temperature
- Up to 2500 deg F (1370 deg C)
- Installation Orientation
- Can be installed to fire in any position (roof, sidewall, etc.)
- Ignition Type
- Direct Spark or Gas Pilot Ignition
- Heat-Up Time
- Immediate ramping to high fire
- Heat Distribution
- Even, with no flame impingement
- Flame Supervision
- UV Scanner or Flame Rod
- Flame Profile
- Flat flame throughout entire firing range
- Flame Geometry
- Short forward flame travel (≈2-6 in/50-150 mm depending on size) (High Fire)
- Excess Air Limits
- 175 to 400% at 16 osig (6900 Pa) inlet air pressure
- Excess Air Capability
- Can operate with excess air limits of approximately 175 to 400% at high inlet air pressure
- Combustion Principle
- Flat flame that hugs the furnace wall to promote radiant heating
- Capacity Range
- Approximately 175,000 to 2,300,000 Btu/h (≈ 47 to 610 kW), size‑dependent (Typical)
- Burner Type
- Wall‑hugging, flat‑flame gas burner
- Burner Sizes
- WHG 112, 115, 120, 125, 130, 140
- Burner Family
- WHG Wall Hugger
- Immediate movement to high fire shortens furnace heat-up.
Applications
- Radiant heating from furnace walls and roofs
Air & Combustion Air Specifications
- Air Temperature Range
- Preheated air up to 800 deg F (425 deg C)
- Excess Air Limits
- 175 to 400% at 16 osig (6900 Pa) inlet air pressure
- Excess Air Capability
- Can operate with excess air limits of approximately 175 to 400% at high inlet air pressure
Processing & Performance Metrics
- Turndown Capability
- Stable operation from low fire to high fire (model‑dependent)
- Capacity Range
- Approximately 175,000 to 2,300,000 Btu/h (≈ 47 to 610 kW), size‑dependent (Typical)
Product Overview & Classification
- Primary Function
- Even heat distribution with no flame impingement
Control, Logic & System Behavior
- Operation Stability
- Stable in cold furnace at low excess air
- Operating Modes
- On‑ratio firing; operation with excess air
Combustion/Furnace/Chamber Temperatures
- Maximum Chamber Temperature
- Up to 2500 deg F (1370 deg C)
Installation & Mounting Specifications
- Installation Orientation
- Can be installed to fire in any position (roof, sidewall, etc.)
Ignition, Flame & Supervision Specifications
- Ignition Type
- Direct Spark or Gas Pilot Ignition
- Flame Supervision
- UV Scanner or Flame Rod
- Flame Profile
- Flat flame throughout entire firing range
- Flame Geometry
- Short forward flame travel (≈2-6 in/50-150 mm depending on size) (High Fire)
Control, Safety & Timing Characteristics
- Heat-Up Time
- Immediate ramping to high fire
Performance, Flow & Capacity
- Heat Distribution
- Even, with no flame impingement
Combustion, Mixing & Fuel Dynamics
- Combustion Principle
- Flat flame that hugs the furnace wall to promote radiant heating
Overview
- Burner Type
- Wall‑hugging, flat‑flame gas burner
Dimensions & Size Specifications
- Burner Sizes
- WHG 112, 115, 120, 125, 130, 140
Product Design & Configuration
- Burner Family
- WHG Wall Hugger
| Parameter | Published value / configuration |
|---|---|
| Air Temperature Range | Preheated air up to 800 deg F (425 deg C) |
| Excess Air Limits | 175 to 400% at 16 osig (6900 Pa) inlet air pressure |
| Excess Air Capability | Can operate with excess air limits of approximately 175 to 400% at high inlet air pressure |
| Turndown Capability | Stable operation from low fire to high fire (model‑dependent) |
| Capacity Range | Approximately 175,000 to 2,300,000 Btu/h (≈ 47 to 610 kW), size‑dependent (Typical) |
| Primary Function | Even heat distribution with no flame impingement |
| Operation Stability | Stable in cold furnace at low excess air |
| Operating Modes | On‑ratio firing; operation with excess air |
| Maximum Chamber Temperature | Up to 2500 deg F (1370 deg C) |
| Installation Orientation | Can be installed to fire in any position (roof, sidewall, etc.) |
| Ignition Type | Direct Spark or Gas Pilot Ignition |
| Flame Supervision | UV Scanner or Flame Rod |
| Flame Profile | Flat flame throughout entire firing range |
| Flame Geometry | Short forward flame travel (≈2-6 in/50-150 mm depending on size) (High Fire) |
| Heat-Up Time | Immediate ramping to high fire |
| Heat Distribution | Even, with no flame impingement |
| Combustion Principle | Flat flame that hugs the furnace wall to promote radiant heating |
| Burner Type | Wall‑hugging, flat‑flame gas burner |
| Burner Sizes | WHG 112, 115, 120, 125, 130, 140 |
| Burner Family | WHG Wall Hugger |
Values retain manufacturer model qualifications. Review Honeywell specifications ↗
Part Number
Published part numbers
10 parts
| Part Number | Description | Enquiry |
|---|---|---|
| 101028467 | KIT,LIT,WHG,WALL HUGGER GAS BURNERS | Request quotation |
| HK12823 | PORT,OBSVTN,1/2 NPT LUBE DEVICES CS2003 | Request quotation |
| HK19560 | TILE ASSY,WHG120 125 RFRCT IGN | Request quotation |
| HK19561 | TILE ASSY,WHG130 140 RFRCT IGN | Request quotation |
| HK19580 | PLT,WHG120 125 FURN MTG | Request quotation |
| HK19581 | BDY,WHG120 125 BRNR | Request quotation |
| HK19582 | BKPLT,WHG120 BRNR | Request quotation |
| HK19583 | BKPLT,WHG125 BRNR | Request quotation |
| HK19586 | PLATE,WHG130-140 FURNACE MOUNTING | Request quotation |
| HK19587 | BDY,RKG/WHG130 140 BRNR | Request quotation |
Manufacturer sources
Last source check: 2026-11-02
Wall Hugger Gas Burners · Manufacturer ownership retained; republication licence not independently confirmed
ABID Automation LTD maintains this independent product reference. Honeywell owns its product names and trademarks. Current manufacturer documentation governs specification, availability and certification.
Your next project. A clear starting point.
Tell us about your facility and what you need to achieve.
