Direct Fired Furnace Burners
Furnnox
Furnnox addresses low-NOx direct furnace heating with on-ratio control across the firing range and preheated combustion air capability.
Furnnox addresses low-NOx direct furnace heating with on-ratio control across the firing range and preheated combustion air capability. Integrated orifices simplify setup, while independently rotatable air and gas inlets adapt the piping layout. Emission performance is application-qualified; the page lists five sizes rather than one fixed output.
Features & Benefits
- Maximum Combustion Air Temperature
- 300 deg F (150 deg C) standard; 1100 deg F (600 deg C) with insulated body
- Minimum Furnace Temperature
- 1400 deg F (760 deg C) (for low NOx)
- Maximum Chamber Temperature
- 2400 deg F (1315 deg C)
- Process Temperature Range
- 2800 deg F (1540 deg C)
- Excess Air Requirement
- Designed for low excess air operation; not suitable for high excess air or process‑air applications
- Pipe Connection Type
- BSP or NPT
- Combustion Principle
- On‑ratio controlled burner for high efficiency
- Gas Orifice Sizes
- 7 mm to 24 mm depending on fuel and model
- Air Orifice Sizes
- 29 mm to 70 mm depending on model
- Flame Detection
- UV Scanner
- Turndown Ratio
- 10:1
- Capacity Range
- 0.25 to 2 MMBtu/h (66 to 530 kW)
- NOx Emissions
- < 30 ppm at 3% O₂ in most high‑temperature furnace applications
- Ignition Type
- Direct ignition anywhere within ignition range; no pilot required
- Flame Length
- Size‑ and fuel‑dependent (approximately 14-43 in/355-1092 mm) (High fire)
- Burner Type
- Ultra‑low NOx direct‑fired furnace burner
- Fuel Type
- Natural Gas, Propane, Butane
- Approvals
- Eurasian Customs Union (Compliant), Honeywell Eclipse Standards (Applies to all models), WEEE Directive Disposal compliance
- Integrated orifices and rotatable inlets reduce piping and setup work.
Applications
- High-temperature direct furnace heating
Detailed capabilities
On-ratio firing with preheated air
Furnnox maintains on-ratio control through its operating range and accepts the stated high combustion-air preheat. Independent 90-degree inlet adjustment changes piping orientation without redefining capacity. Five sizes are described. The source qualifies the low-NOx value to most high-temperature applications at a stated oxygen reference, so it should not be presented as the unconditional emission level in every cold or altered-ratio installation.
Features and benefits
- Integrated orifices and rotatable inlets reduce piping and setup work.
Published application context
- High-temperature direct furnace heating
Overview
- Models
- FN0025, FN0050, FN0100, FN0150, FN0200
- Burner Type
- Ultra‑low NOx direct‑fired furnace burner
Combustion/Furnace/Chamber Temperatures
- Maximum Combustion Air Temperature
- 300 deg F (150 deg C) standard; 1100 deg F (600 deg C) with insulated body
- Minimum Furnace Temperature
- 1400 deg F (760 deg C) (for low NOx)
- Maximum Chamber Temperature
- 2400 deg F (1315 deg C)
Operating/Process Temperature Ranges
- Process Temperature Range
- 2800 deg F (1540 deg C)
Air & Combustion Air Specifications
- Excess Air Requirement
- Designed for low excess air operation; not suitable for high excess air or process‑air applications
- Air Orifice Sizes
- 29 mm to 70 mm depending on model
Connections & Interfaces
- Pipe Connection Type
- BSP or NPT
Combustion, Mixing & Fuel Dynamics
- Combustion Principle
- On‑ratio controlled burner for high efficiency
Dimensions & Size Specifications
- Gas Orifice Sizes
- 7 mm to 24 mm depending on fuel and model
Ignition, Flame & Supervision Specifications
- Flame Detection
- UV Scanner
- Ignition Type
- Direct ignition anywhere within ignition range; no pilot required
Performance, Flow & Capacity
- Turndown Ratio
- 10:1
Processing & Performance Metrics
- Capacity Range
- 0.25 to 2 MMBtu/h (66 to 530 kW)
- NOx Emissions
- < 30 ppm at 3% O₂ in most high‑temperature furnace applications
Burner/Flame‑Related Lengths
- Flame Length
- Size‑ and fuel‑dependent (approximately 14-43 in/355-1092 mm) (High fire)
Applications & Compatibility
- Applications
- Continuous high‑temperature furnaces (annealing/pickling lines), forging furnaces, heat‑treatment furnaces, galvanizing furnaces, slot‑type forge furnaces
Fuel, Gas & Media Specifications
- Fuel Type
- Natural Gas, Propane, Butane
Standards & Certifications
- Approvals
- Eurasian Customs Union (Compliant), Honeywell Eclipse Standards (Applies to all models), WEEE Directive Disposal compliance
| Parameter | Published value / configuration |
|---|---|
| Models | FN0025, FN0050, FN0100, FN0150, FN0200 |
| Burner Type | Ultra‑low NOx direct‑fired furnace burner |
| Maximum Combustion Air Temperature | 300 deg F (150 deg C) standard; 1100 deg F (600 deg C) with insulated body |
| Minimum Furnace Temperature | 1400 deg F (760 deg C) (for low NOx) |
| Maximum Chamber Temperature | 2400 deg F (1315 deg C) |
| Process Temperature Range | 2800 deg F (1540 deg C) |
| Excess Air Requirement | Designed for low excess air operation; not suitable for high excess air or process‑air applications |
| Air Orifice Sizes | 29 mm to 70 mm depending on model |
| Pipe Connection Type | BSP or NPT |
| Combustion Principle | On‑ratio controlled burner for high efficiency |
| Gas Orifice Sizes | 7 mm to 24 mm depending on fuel and model |
| Flame Detection | UV Scanner |
| Ignition Type | Direct ignition anywhere within ignition range; no pilot required |
| Turndown Ratio | 10:1 |
| Capacity Range | 0.25 to 2 MMBtu/h (66 to 530 kW) |
| NOx Emissions | < 30 ppm at 3% O₂ in most high‑temperature furnace applications |
| Flame Length | Size‑ and fuel‑dependent (approximately 14-43 in/355-1092 mm) (High fire) |
| Applications | Continuous high‑temperature furnaces (annealing/pickling lines), forging furnaces, heat‑treatment furnaces, galvanizing furnaces, slot‑type forge furnaces |
| Fuel Type | Natural Gas, Propane, Butane |
| Approvals | Eurasian Customs Union (Compliant), Honeywell Eclipse Standards (Applies to all models), WEEE Directive Disposal compliance |
Values retain manufacturer model qualifications. Review Honeywell specifications ↗
Part Number
Published part numbers
10 parts
| Part Number | Description | Enquiry |
|---|---|---|
| 10012903 | CMBSTR,BRNR,FN0025 | Request quotation |
| 10012904 | CMBSTR,BRNR,FN0050 | Request quotation |
| 10012906 | CMBSTR,BRNR,FN0100 | Request quotation |
| 10012907 | CMBSTR,BRNR,FN0150 | Request quotation |
| 10012928 | PLT,ADPT,DIST,AIR,ASY,FN0150 | Request quotation |
| 10012929 | PLT,ADPT,DIST,AIR,ASY,FN0200 | Request quotation |
| 10012966 | GSKT,MTG,BLCK,FN0025,INSULFRAX MATL | Request quotation |
| 10012967 | GSKT,MTG,BLCK,FN0050,FN0075 INSULFRAX MA | Request quotation |
| 10012969 | GSKT,MTG,BLCK,FN0100,INSULFRAX MATL | Request quotation |
| 10012970 | GSKT,MTG,BLCK,FN0150,INSULFRAX MATL | Request quotation |
Manufacturer sources
Last source check: 2026-11-02
Furnnox Product Image · Manufacturer ownership retained; republication licence not independently confirmed
Furnnox Product Image 1 · Manufacturer ownership retained; republication licence not independently confirmed
Furnnox Flame Image 1 · Manufacturer ownership retained; republication licence not independently confirmed
Furnnox Flame Image · Manufacturer ownership retained; republication licence not independently confirmed
ABID Automation LTD maintains this independent product reference. Honeywell owns its product names and trademarks. Current manufacturer documentation governs specification, availability and certification.
Your next project. A clear starting point.
Tell us about your facility and what you need to achieve.
