Fire & Life Safety · Building Systems · Industrial Automation [email protected] +880 1347 561 256
Honeywell Process Measurement & Control

Conductivity

4909 Ball Valve or Insertion Mounting

4909 conductivity assemblies use a ball valve to insert or remove a sensor from a tank or large pipe without stopping the process.

4909 conductivity assemblies use a ball valve to insert or remove a sensor from a tank or large pipe without stopping the process. Stainless-steel and CPVC arrangements are published, with several cell constants for different liquids. The assembly includes the valve and mounting hardware; Honeywell identifies 4908 as the replacement cell used within this arrangement.

Features & Benefits

Assembly
Ball valve, nipple, stuffing box and cell
  • Allows sensor removal without interrupting the process

Applications

  • Industrial and high-purity-water conductivity measurement

Detailed capabilities

What Is It?

4909 includes the ball valve, nipple, stuffing box and conductivity cell for mounting in a pipe or tank wall. 4908 is only its replacement cell. Stainless-steel or CPVC assemblies and different electrode/cell-constant choices adapt the measurement; ordering a 4908 alone does not supply the complete insertion assembly.

Manufacturer reference ↗

How Does It Work?

The ball valve allows cell insertion or removal without stopping the process, within the stated pressure/temperature requirements. The source lists operation to 140°C and 150 psig. Nickel, Monel or platinum electrodes depend on the required cell constant, while the corrosion-resistant body and sealing assembly maintain the process interface during the approved sequence.

Manufacturer reference ↗

What Problems Does It Solve?

Conductivity observation supports water purity, contamination detection, chemical-strength verification and scaling/corrosion management. The removable mounting reduces process interruption for cell service. Material, cell constant and pressure must still match the application rather than treating the ball valve as permission to remove any configuration under arbitrary operating conditions.

Manufacturer reference ↗

Specifications

Communication & Protocols

Cell Constants Supported
0.01, 0.1, 1, 10, and 50 cm⁻¹

Technical Specifications

Electrical Connections
4 or 6 leads with integral Automatic Temperature Compensator and EEPROM (DL4000)
Process Connections
CPVC: 1-1/2 in MNPT; Stainless Steel: 1-1/4 in MNPT

I/O Capabilities

Purge Port Connection
CPVC: 1/4 in NPT female (for Debris Flushing)
Insertion Depth
CPVC: 114 to 173 mm (4.5 to 6.8 in); Stainless Steel: 165 to 224 mm (6.5 to 8.8 in)
Mounting Types
Ball Valve (insertion/removal without process interruption), Insertion Mounting

Network & Connectivity Infrastructure

Removal Total Length
CPVC: 914 mm (36 in) or 1067 mm (42 in) with Extension Tube; Stainless Steel: 1130 mm (44.5 in) or 1238 mm (50.5 in) with Junction Head
Overall Length
CPVC: 502 mm (19.7 in) or 564 mm (22.2 in) with Junction Head; Stainless Steel: 422 mm (16.6 in) or 521 mm (20.5 in) with Junction Head

Mechanical & Physical Properties

Electrode Materials
Nickel, Monel, or Platinum (constants 10 and higher are platinized)
Wetted Materials
CPVC: CPVC Ball Valve, Viton, Teflon and EPDM Seals, PES Cell, Nickel/Platinum/Monel Electrodes; Stainless Steel: 316 Stainless Steel Ball Valve, Viton and Teflon Seals, PES Cell, Nickel/Platinum/Monel Electrodes

Environmental Conditions

Temperature Rating
Up to 140 deg C (284 deg F) at 200 psig (SS); Up to 80 deg C (176 deg F) at 50 psig (CPVC)
Pressure Ratings
50 psig max @ 80 deg C (176 deg F); 90 psig max @ 50 deg C (122 deg F); Removal/insertion up to 50 psig, CPVC: 125 psig max @ -5 deg C (23 deg F); Stainless Steel: 200 psig (1379 kPa) max at 140 deg C (284 deg F)

Material Specifications

Cell Body Material
316 Stainless Steel or CPVC Plastic

Standards & Certifications

Approvals
ASME Section VIII, Div. 1, UG-101, CRN #0F11607-5C

Wiring / Mechanical & Physical Properties

Leadwire
Tefzel-Covered 18-gage Cable, 20 ft Long (longer via junction box)
4909 Ball Valve or Insertion Mounting — manufacturer page values
ParameterPublished value / configuration
Cell Constants Supported0.01, 0.1, 1, 10, and 50 cm⁻¹
Electrical Connections4 or 6 leads with integral Automatic Temperature Compensator and EEPROM (DL4000)
Process ConnectionsCPVC: 1-1/2 in MNPT; Stainless Steel: 1-1/4 in MNPT
Purge Port ConnectionCPVC: 1/4 in NPT female (for Debris Flushing)
Insertion DepthCPVC: 114 to 173 mm (4.5 to 6.8 in); Stainless Steel: 165 to 224 mm (6.5 to 8.8 in)
Mounting TypesBall Valve (insertion/removal without process interruption), Insertion Mounting
Removal Total LengthCPVC: 914 mm (36 in) or 1067 mm (42 in) with Extension Tube; Stainless Steel: 1130 mm (44.5 in) or 1238 mm (50.5 in) with Junction Head
Overall LengthCPVC: 502 mm (19.7 in) or 564 mm (22.2 in) with Junction Head; Stainless Steel: 422 mm (16.6 in) or 521 mm (20.5 in) with Junction Head
Electrode MaterialsNickel, Monel, or Platinum (constants 10 and higher are platinized)
Wetted MaterialsCPVC: CPVC Ball Valve, Viton, Teflon and EPDM Seals, PES Cell, Nickel/Platinum/Monel Electrodes; Stainless Steel: 316 Stainless Steel Ball Valve, Viton and Teflon Seals, PES Cell, Nickel/Platinum/Monel Electrodes
Temperature RatingUp to 140 deg C (284 deg F) at 200 psig (SS); Up to 80 deg C (176 deg F) at 50 psig (CPVC)
Pressure Ratings50 psig max @ 80 deg C (176 deg F); 90 psig max @ 50 deg C (122 deg F); Removal/insertion up to 50 psig, CPVC: 125 psig max @ -5 deg C (23 deg F); Stainless Steel: 200 psig (1379 kPa) max at 140 deg C (284 deg F)
Cell Body Material316 Stainless Steel or CPVC Plastic
ApprovalsASME Section VIII, Div. 1, UG-101, CRN #0F11607-5C
LeadwireTefzel-Covered 18-gage Cable, 20 ft Long (longer via junction box)

Values retain manufacturer model qualifications. Review Honeywell specifications ↗

Resources

Filter documents by type

Resources linked from the manufacturer’s page. Confirm the document revision and applicable model before installation or ordering.

Honeywell resource listing ↗
Manufacturer sources

https://process.honeywell.com/us/en/products/process-instruments/analytical-instruments-and-sensors/conductivity/4909-ball-valve-or-insertion-mounting

Last source check: 2026-11-02

4909 Ball Valve or Insertion Mounting Image · Manufacturer ownership retained; republication licence not independently confirmed

ABID Automation LTD maintains this independent product reference. Honeywell owns its product names and trademarks. Current manufacturer documentation governs specification, availability and certification.

Your next project. A clear starting point.

Tell us about your facility and what you need to achieve.

CallSend enquiry