Fire & Life Safety · Building Systems · Industrial Automation [email protected] +880 1347 561 256
Honeywell Process Measurement & Control

CD Actuator Systems

CalCoil PRO

Calcoil Pro uses induction heating to adjust calender-roll temperature for cross-direction caliper control and finishing.

Calcoil Pro uses induction heating to adjust calender-roll temperature for cross-direction caliper control and finishing. Individually controlled coils sit close to the roll without mechanical contact and are contoured for the installation. The system combines these actuators with power modules and control software, supporting localized heating and sheet-profile adjustment without adding a drive load to rotate the roll.

Models: 9760-00, 9760-01, 9760-10, 9760-11

Features & Benefits

Technology
Non-contact induction heating
Actuation
Individually controlled contoured workcoils
  • Supports efficient localized roll heating

Applications

  • Paper calender caliper control and finishing

Detailed capabilities

Product and configuration

Calcoil Pro uses induction heating to adjust calender-roll temperature for cross-direction caliper control and finishing. Individually controlled coils sit close to the roll without mechanical contact and are contoured for the installation. The system combines these actuators with power modules and control software, supporting localized heating and sheet-profile adjustment without adding a drive load to rotate the roll.

  • Technology: Non-contact induction heating
  • Actuation: Individually controlled contoured workcoils

Manufacturer reference ↗

Operation and integration

Calcoil PRO uses alternating-current induction to heat a calender roll without contacting it or adding roll drive load. Contoured, epoxy-protected workcoils form independently controlled zones; two zones share a shoe. The published working gap is 3–7 mm for effective magnetic coupling.

Manufacturer reference ↗

Application and selection

Localized roll heating changes nip loading for cross-direction caliper correction, while average power influences gloss or smoothness in the machine direction. The actuator system supports finishing quality, runnability and lower rejects, with coil contour and installation matched to the roll.

Manufacturer reference ↗

Case studies & further resources

Manufacturer Document

Calcoil PRO Models 9760-00, 9760-01, 9760-10, 9760-1 PIN

View resource ↗

Specifications

Environmental Conditions

Power Module Cooling Air Supply Temperature
20 to 40 deg C; 68 to 104 deg F

Electrical Specifications

Power Module Cooling Air Flow
1.2 to 1.4 Nm3/min; 42 to 48 SCFM

Mechanical & Physical Properties

Actuator Zone Width
2.95 in; 75 mm

Others

Models
9760-00; 9760-01; 9760-10; 9760-11
Power Module Cooling Air Supply Inlet Pressure
50 to 90 mm H2O
Maximum Output Power
4500 W; 4500 to 6000 W
Energy Efficiency
0.94
Construction Type
High Temperature Epoxy; Water Cooled
Input Frequency
50 or 60 Hz hertz
Input Voltage
3 phase 380~456 VAC voltage alternating current
Input Power
5 kVA voltage direct current; 5 to 6.7 kVA voltage direct current
Standards
CSA; UL
CalCoil PRO — manufacturer page values
ParameterPublished value / configuration
Power Module Cooling Air Supply Temperature20 to 40 deg C; 68 to 104 deg F
Power Module Cooling Air Flow1.2 to 1.4 Nm3/min; 42 to 48 SCFM
Actuator Zone Width2.95 in; 75 mm
Models9760-00; 9760-01; 9760-10; 9760-11
Power Module Cooling Air Supply Inlet Pressure50 to 90 mm H2O
Maximum Output Power4500 W; 4500 to 6000 W
Energy Efficiency0.94
Construction TypeHigh Temperature Epoxy; Water Cooled
Input Frequency50 or 60 Hz hertz
Input Voltage3 phase 380~456 VAC voltage alternating current
Input Power5 kVA voltage direct current; 5 to 6.7 kVA voltage direct current
StandardsCSA; UL

Values retain manufacturer model qualifications. Review Honeywell specifications ↗

Resources

Filter documents by type

Resources linked from the manufacturer’s page. Confirm the document revision and applicable model before installation or ordering.

Honeywell resource listing ↗

Part Number

Published model / variant identifiers. A full ordering code requires the manufacturer configuration.

Manufacturer sources

https://process.honeywell.com/us/en/products/process-automation/quality-control-systems-qcs/cd-actuator-systems/calcoil-pro

Last source check: 2026-11-02

CalCoil PRO Product Image · Manufacturer ownership retained; republication licence not independently confirmed

ABID Automation LTD maintains this independent product reference. Honeywell owns its product names and trademarks. Current manufacturer documentation governs specification, availability and certification.

Your next project. A clear starting point.

Tell us about your facility and what you need to achieve.

CallSend enquiry